Speedo sensor on ABS equipped models, used for front and rear applications depending on model

Used as rear wheel ABS sensor on V85TT, front and rear sensor on V7 II ABS equipped models. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering. Supercedes Guzzi ref. 6429875. 2 pin connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 859792 MG859792

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours

Switch used as rear stop switch or clutch switch

Used as rear stop light switch on V85TT

 This part is available by special order, request a quote

2D000325

Also fits Aprilia RSV 1000, Aprilia Tuono

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

NGK iridium MR8BI-8 spark plug

 This part is due back in stock soon, call 01484 841395 to reserve yours

1A010638

Also fits Aprilia DORSODURO 900 J ABS (2018-202), Aprilia SHIVER 900 (2017-2020), Piaggio LIBERTY 50 3V I-GET (2017-2018), Vespa PRIMAVERA 50 4T 3V N (2022), Vespa PRIMAVERA 50 4T 3V N (2022), Vespa SPRINT 50 4T (2018), Vespa SPRINT 50 4T 3V N S (2022)

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Oil pressure switch M10 thread

Supercedes Guzzi no. 1A014570

 This part is due back in stock soon, call 01484 841395 to reserve yours

1A017929

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Spark plug cap

Also known as suppressor cap. Guzzi ref. 1A005382

 1 in stock

1A010839

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock